UK Nationwide Professional Snagging Inspections | Getting the Quality You Deserve

Air Source Heat Pumps in New Build Homes

More and more new build homes now come with an air source heat pump instead of a gas boiler, and for many buyers it is their first experience of one. The first cold spell of winter often brings a wave of questions. Why do the radiators only feel warm? Why is the unit outside running all day? And why is there a cloud of steam coming off it?

Some of this is perfectly normal. Some of it is a snag that your developer should put right. And occasionally the problem lies in how the system was designed or set up, which needs a different approach. This guide explains the difference, what you should be given when you move in, and what to look for.

Heat pumps are only going to become more common. The Future Homes and Buildings Standards, which come into force in England on 24 March 2027, are designed to ensure new homes are built with low carbon heating and high levels of energy efficiency.

How a heat pump differs from a gas boiler

A heat pump takes heat from the outside air and upgrades it to warm your home and hot water. It works most efficiently at lower water temperatures than a boiler, running more gently for longer periods rather than in short, hot bursts.

The rules reflect this. In England, Approved Document L says a new wet heating system should be sized to heat the home effectively at a maximum flow temperature of 55°C or lower. The NHBC Standards 2026 go further for heat pumps, with designs based on a mean water temperature of 42.5°C or lower and radiators or underfloor heating sized to match. In practice, that means radiators that feel warm rather than hot to the touch, and often larger radiators than you might expect.

In cold, damp weather you may also see the outdoor unit give off a plume of vapour and drip water. The NHBC Standards say air source systems should have an automatic defrost cycle and suitable condensate drainage, so this is the unit clearing frost from itself, not a fault.

How your system is best run, for example whether it should be left on a steady temperature or set back overnight, depends on the system and how it was designed. Ask your developer or the installer for advice specific to your home, rather than relying on general tips.

What your developer should give you at handover

Good information at handover makes a real difference to how comfortable your home is and how much it costs to run. In England, Approved Document L says the owner of a new home should receive operating and maintenance instructions that are easy to understand and specific to the home. They should explain what each system is, what it does, where it is located, how to operate it (including timers and sensors) and how to maintain it, and include a completed commissioning sheet where relevant. They should also include a Home User Guide giving non-technical advice on ventilation, heating and hot water.

The NHBC Standards set out a similar handover pack, including user instructions, contact details for the manufacturers and installers, a commissioning or compliance certificate (for example Benchmark, MCS or a suitable alternative), maintenance and servicing requirements, warranties, and guidance on using the system efficiently to keep running costs down. If your home is covered by a different warranty provider, it will have its own technical standards, but you should still expect clear instructions.

If you can, ask the developer to show you how the controls work before or on the day you move in, and check that you know where the documents are kept. If anything is missing, ask for it in writing.

Snags to look for

Many heat pump issues are visible and easy to spot with a careful look, both outside and in. Things worth checking include:

  • the outdoor unit is securely fixed, stable, undamaged and has space around it for airflow and maintenance, as the manufacturer recommends
  • condensate drains away properly, and is not discharging across a path or patio where it could freeze in winter
  • pipework is insulated, especially where it runs outside, and the insulation is complete and undamaged
  • holes where pipes and cables pass through the wall are properly sealed and weatherproofed
  • there is no excessive noise, rattling or vibration from the unit, its brackets or the pipework
  • inside, the hot water cylinder and pipework are insulated, there are no leaks, and the controls and thermostats work in every heating zone
  • every radiator or underfloor heating zone actually warms up

The NHBC Standards say the connection between a heat pump and the building should be weather resistant and sealed, and that weatherproofing that relies solely on sealant is not acceptable. A blob of mastic around a pipe where it enters the wall is worth flagging.

Underfloor heating is common with heat pumps, and the floor will only ever feel gently warm. That is normal. A room that never warms up, despite the controls being set correctly, is not.

When it is more than a snag

Some of the most frustrating heat pump problems are not about workmanship at all. If rooms stay cold despite the system being set up as instructed, the cause may lie in the design, such as the heat loss calculations or the size of the radiators, or in how the system was commissioned.

The NHBC Standards say a heat pump should be able to provide at least 100% of the home’s calculated heating requirement in winter design conditions, with heat loss calculations carried out in line with recognised standards. A snagging inspection looks at the quality of the installation and finish that can be seen. It cannot check design calculations or test how a system performs over a whole winter, so these problems need a different route.

If you think something is wrong, start by keeping a simple record of room temperatures, outside temperatures, your control settings and dates. Report the problem to your developer in writing and ask for a copy of the heat loss calculations and commissioning records. Your developer is responsible for putting defects right during the first two years, and if you are not getting anywhere, your warranty provider may be able to help. If your developer is registered under the New Homes Quality Code, you can also take an unresolved complaint to the New Homes Ombudsman Service. For a technical opinion on the design or performance of the system, you may need an independent, suitably qualified heating engineer. Our Defect Escalation Process page explains how to take matters further.

A few habits that help

Read your Home User Guide and keep it somewhere handy. Keep the outdoor unit clear of leaves, snow and anything stored against it, and do not box it in. Follow the servicing requirements in your handover pack, as these may affect the manufacturer’s warranty. And keep your ventilation working as designed, because a well-ventilated home is easier to heat comfortably and less prone to condensation.

How a snagging inspection helps

A professional snagging inspection checks the visible installation along with the rest of your home, from the outdoor unit and pipework to radiators, controls and the finish around them. Our Standard Inspection includes a thermal inspection, which can help reveal cold spots and heat loss around doors, windows and radiators. If you are still to complete, a Pre-Completion Inspection follows the NHQB checklist before you move in, although NHQB rules mean thermal imaging cannot be included at that stage.

If you are already noticing cold rooms, you may find our articles The Role of Thermal Imaging in Solving Cold Room Problems and Part L Building Regulations: What New Homeowners Need to Know About Multi-Zone Heating Systems helpful, along with our guide to what the NHBC Standards say about your new home’s internal services. Completing over the winter? Our guide Completing on a New Build Before Christmas? Why the Year-End Rush Matters for Snagging covers what to watch for.

If you would like an independent check of your new home, heating included, you can book online, view our fees or get in touch. We are always happy to help.

Share: